Ether.Genius Synchronization

ALBEDO Ether.Genius is an multitechnology tester equipped with all the features to install and troubleshoot telecom networks based on Gigabit Ethernet (GbE),Synchronous Ethernet (SYNCE), Precision Time Protocol (PTP IEEE 1588), E1, 2Mbit/s, Jitter, Wander, Datacom, C37.94 test, nx64k, Voice Frequency and more.

You may buy just a last generation dual port GbE tester --with exactly the same specification than ALBEDO Ether.Giga-- and then you may add any technology just when you need it by a simple and easy soft upgrade to get the new firmware, to include the new funtionalities.

  • No modules: no problems.
  • No modules: all the interfaces are always there.
  • No modules: no silly connectors, perfect connections.
  • No modules: you will never ever lost/forget/broke a module again.

GbE Features

  • Y.1564 (e-SAM) FTD, 2-way FDV, FDV, 2-way FTD, FLR, SES, PEU and PEA
  • Y.1731 QoS statistics
  • 2 x SFP + 2 x RJ45 interfaces
  • Symmetrical & Asymmetrical RFC2544 test
  • FCS error insertion in passthrought mode
  • L1/L2/L3/L4 loopback
  • Multistreams for IPTV, VoIP, and Critical Data verification
  • Q-in-Q for demarcation tests
  • MPLS support
  • Scan MAC/IP/VLAN/QinQ
  • Advanced Counts: Up to 8 filters at MAC, IP, TCP/UDP, Arbitrary [mask + offset]
  • Migrable to Synchronous Ethernet (SyncE)

SyncE Features

  • Synchronization according G8261, G8262, G8264
  • Ethernet Line frequency (MHz), offset (ppm), drift (ppm/s)
  • Analysis / Generation ESMC messages and SSM count and rate
  • Ext. clock input including 2048 kb/s, 2048 Hz, and Synchronous Ethernet
  • SyncE MTIE / TDEV measurement
  • SyncE Wander analysis/generation
  • PTP / IEEE 1588v2 support decoding
  • PTP support / generation as master or slave
  • Master Clock operation on each port using internal/external ref.
  • Y.1564 (e-SAM) FTD, 2-way FDV, FDV, 2-way FTD, FLR, SES, PEU & PEA
  • Y.1731 QoS statistics
  • 2xSFP + 2 x RJ45 i/faces
  • Symmetrical & Asymmetrical RFC2544 test
  • FCS error insertion in passthought mode
  • L1/L2/L3/L4 loopback
  • Multistreams for IPTV, VoIP, and Critical Data verification
  • Q-in-Q for demarcation tests
  • MPLS support
  • Scan MAC/IP/VLAN/QinQ
  • Advanced Counts: Up to 8 filters at MAC, IP, TCP/UDP, Arbitrary

E1 Features

  • Port A: Coaxial Pair Impedance: 75 Ohm BNC unbalanced and 120 Ohm RJ-45 balanced
  • Port B: Symmetrical Pair Impedance 120 Ohm RJ-45 balanced
  • Analogue voice frequency audio port.
  • Additional balanced secondary E1 port 0 to -6dB, nominal and PMP -20dB
  • Operation: Terminal, Through and Monitor
  • Bit Rate: 2048 Kbit/s (+/- 3ppm)
  • Codes: HDB3 / AMI
  • Unframed
  • PCM31: FAS / FAS+CRC4
  • PCM30: FAS+CAS / FAS+CRC
  • Force Single Error: Bit, Frame, CRC, and BPV (Bipolar Violation)
  • G.826, G.821, and M.2100
  • RTD and VF tone generation
  • Alarms and errors count, and generation

Jitter Wander Features

  • ITU-T G.823 compliant (jitter)
  • Overpass O.172
  • Jitter level, tolerance, transfer
  • Event detection
  • 100% digital based generation and analyzer
  • Wander Generation and Measurements (TIE, MTIE, TDEV)
  • Wander results from 20 to 100 000s

Datacom Features

  • Smart Serial 26p DTE / DCE ports
  • V.11/X.24, V.24/V.28, V.24/V.35, V.24/V.11 (V.36/RS449), EIA530 and EIA-530A
  • Codirectional according G.703
  • Rate: 50, 60 bit/s, 1.2, 2.4, 4.8, 8, 9.6, 16, 19.2, 32, 48, 72, 128, 144, 192, 1544 kbit/s
  • N x 56 kbit/s (N=1 to 27); N x 64 kbit/s (N=1 to 32), up to 10 Mbit/s
  • DTE, DCE emulation and monitor

C37.94 Measurement

  • Test Rate: N x 64 kbit/s, N = 1 to 12
  • Configuration of internal, recovered clock
  • Frame/Unframed BER test patterns
  • ITU-T G.821 performance: ES, SES, UAS, DM.
  • Results with pass / fail indications Test pattern generation / analysis
  • Frequency (Hz), Deviation (ppm), Max deviation
  • Round Trip Delay (ms).
  • Defects: LOC, AIS, LOF, RDI, LSS, All 0, All 1
  • Anomalies: FAS, TSE, Slip

Users

  • Wimax, LTE operators
  • Power utilities
  • Telecom Installers and Operators
  • Network Clock manufacturers
  • Triple Play service providers
  • R&D, Universities, Labs
  • Commission / Maintenance

 

Ordering Information

CODEDESCRIPTION

AT.EGenius.HHEther.Genius hand-held tester. Battery operated. GBE tester with optional E1, data communications and synchronization capabilities includes dual 10/100/1000 Mb/s electrical ports, dual optical ports. QoS statistics, RFC2544 performance test, BER test, continuous / burst / ramp / random traffic generation, traffic statistics, error analysis, connectivity test (PING, Trace Route), analysis filters, event insertion, endpoint and through operation modes, graphical display of events, report generation and export. Includes AC/DC adapter, transportation bag, one RJ-45 patch cable, One BNC-BNC patch cable. SFP transceivers not included.

AT.EGenius.MstrMultistream Test. Generation over eight independent traffic streams. Eight analysis filters for each test port.

AT.EGenius.1564eSAM (ITU-T Y.1564). Test of up to 8 services simultaneously. Set up of CIR, EIR and policing rate. Per stream quality objectives. Measurement of Information rate (IR), Frame Transfer Delay (FTD), Frame Delay Variation (FDV), Frame Loss Ratio (FLR) and Availability.
[REQUIRES: AT.EGenius.Mstr]

AT.EGenius.IPV6IPV6 test. Decoding and analysis of IPV6 datagrams. IPV6 traffic statistics and events. IPV6 packet filtering. Top IPV6 source and destination address (with Network Search option).

AT.EGenius.MPLSMPLS test. Generation of a single or double label according RFC 3032. Configuration of TTL, Traffic class, Label . Filter selection rules by Label and Traffic class field. Frame analysis of MPLS Packets. Top LSPs (with Network search option).

AT.EGenius.WIRECable test. Wiremap with open and short circuit detection. Measurement of distance to fault. Crossover / straight cable detection. Measurement of the cable skew.

AT.EGenius.POEPower over Ethernet test. PoE / PoE+ end point and pass through as per IEEE 802.3af and IEEE 802.3at with voltage and current measurement.

AT.EGenius.NSNetwork Search. Automatic detection of up 16 most frequent streams listed by IPV4, VLAN and MAC.

AT.VNC.RCGraphical Remote Control. Based on VNC for Windows and Linux. Ethernet/IP remote control that duplicates the tester graphical user interface in a remote computer. 

AT.SNMP.RCSNMP Remote Control and Automation. Based on SNMP protocol allows user to control the tester remotelly using SNMP queries. 

AT.20Car charger. Power adapter to charge the test unit from car battery.

AT.Lipo.BattAdditional Lipo battery.

ETHER.GENIUS - E1 & DATACOM Software Options

AT.EGenius.E1E1 test. ITU-T G.703 2048 kb/s testing including BNC and RJ48 connectors, E1 generation and analysis ; internal, recovered and external clock references; G.821, G.826 and M.2100 performance analysis; frequency and received power level measurements; CAS ABCD bits generation and analysis; delay measurement.

AT.EGenius.DataDatacom. DTE / DCE emulation and datacom monitor modes. V.24/V.28 (RS-232) asynchronous and synchronous interfaces, X.21/V.11, V35, V36 (RS-449), EIA-530, EIA-530A. No datacom cables included.
[REQUIRES AT.EGenius.E1]

AT.EGenius.JWE1 Jitter / Wander. Peak-to-peak jitter, RMS jitter, max. jitter, jitter hits detection. Configuration of jitter filters. Frequency offset (ppm), frequency drift (ppm/s). Wander metrics (TIE, MTIE, TDEV). Sinusoidal jitter and wander generation.
[REQUIRES AT.EGenius.E1]

AT.EGenius.PulsePulse Mask Analysis. Displays the pulse shape and checks compliance with ITU-T G.703 mask. Includes eye diagram operation mode and analysis of pulse time and level metrics.
[REQUIRES AT.EGenius.E1]

AT.EGenius.V.24V.24/V.28/RS-232 cables. V.24/V.28/RS-232 DTE and DCE interface cables.

AT.EGenius.X.21X.21/V.11 cables. X.21/V.11 DTE and DCE interface cables.

AT.EGenius.V.35V.35 cables. V.35 DTE and DCE interface cables.

AT.EGenius.V.36V.36/RS-449 cables. V.36/RS-449 DTE and DCE interface cables.

AT.EGenius.530EIA-530 / EIA-530A cables. EIA-530 / EIA-530A DTE and DCE interface cables.

AT.80VF adapter.  G.711 test, PCM, level and frequency.

AT.86Stereo audio adapter. Stereo audio input adapter.

AT.88Codirectional adapter. Input / output, Smart Serial to DIN41628 (4 mm Siemens type) connector, G.703 E0 interface.

AT.89C37.94 Adapter. Input / output, Smart Serial to SFP, IEEE C37.94 interface.

AT.90RJ48 to RJ48 E1 crossover cable.

AT.91Sync adapter. Smart Serial to RJ45. External reference clock input 1 PPS. External reference clock output 1 PPS. Additional external reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz. Additional external reference clock output 2048 kHz.

AT.HSHead-Set 2.5mm jack  Integrated Headphone and Microphone

ETHER.GENIUS – SyncE & PTP Software Options

AT.EGenius.SESyncE Clock Emulation. Synchronization testing according to ITU-T G.8261, G.8262, G.8264. Ethernet line frequency (MHz), offset (ppm), drift (ppm/s). Analysis / Generation of ESMC messages. External reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz, Synchronous Ethernet and 1 PPS. External reference clock output 2048 kHz and 1 PPS. 1PPS input / output adapter not included.

AT.EGenius.SEWSyncE Wander test. Synchronous Ethernet  TIE / MTIE / TDEV measurement. Synchronous Ethernet wander generation.
[REQUIRES: AT.EGenius.SE]

AT.EGenius.PTPIEEE 1588v2 / PTP Clock Emulation. PTP master and slave emulation. PTP passive monitoring. PTP message classification and analysis. PDV analysis. External reference clock input 2048 kbit/s, 2048 kHz, 10 MHz and Synchronous Ethernet. External reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz, Synchronous Ethernet and 1 PPS. External reference clock output 2048 kHz and 1 PPS.

AT.EGenius.PTPWIEEE 1588v2 / PTP wander test. PTP TIE / MTIE / TDEV measurement.
[REQUIRES: AT.EGenius.PTP]

AT.EGenius.OCXOOCXO time reference. High performance internal oscillator replacing the standard time reference installed in the application board. 

AT.EGenius.GPSGPS receiver and antenna. Provides absolute time reference for synchronization tests through the GPS satellite network. Connection is through RJ-45 male interface.

ETHER.GENIUS - Interfaces

AT.Wi-Fi.RCWi.Fi USB Remote Control wireless interface to be used together with VNC. 
[REQUIRES: AT.VNC.RC]

AT.1000Sx.SFPSFP Adapter 1.25 Gbps SFP, 850 nm, MMF, 500 m reach, w/ DDM, Duplex LC, 0 - 70ªC

AT.1000Lx.SFPSFP Adapter 1.25 Gbps SFP, 1310 nm, SMF, 20 Km reach, w/ DDM, Duplex LC, 0 - 70ªC

AT.1000Zx.SFPSFP Adapter 1.25 Gbps SFP, 1550 nm, SMF, 80 Km reach, w/ DDM, Duplex LC, 0 - 70ªC

AT.Elect.SFPSFP Adapter 10/100/1000BT Electrical SFP transceiver, SGMII, 0 – 70ºC

AT.100Fx.SFPSFP Adapter 100FX, 125 Mbps SFP, 1310 nm, MMF, 2Km reach, w/ DDM, SGMII, Duplex LC,  0 – 70ºC

AT.C37.94Sx.SFPIEEE C37.94 SFP Adapter 2048 Kb/s SFP, 850 nm, MMF, Duplex LC, 0 – 70ºC

Calibration Services

AT.Egenius.CertCertificate of calibration. Accuracy calibration certificate, executed only when is sold and before its shipment.  

AT.Egenius.Check

Periodical Unit Verification. Includes board test verification (Calibration, Internal Frequency), test port verification (Ports A / B / C: Ethernet, SFP, unbalanced E1, balanced E1, VF Port , DTE / DCE Ports) and analog verification (level port A / B / C, line attenuation, jitter error, pulse mask).

Suscribirse a